请问ATP报出如下错误怎么办

星轨

3 x6 ~! ]( O1 {+ v8 d! t8 {1 c* A
  a6 s1 d9 t) C# f/ k8 o

ATP报错截图

7 K" u- f) O( ]3 {那位老师可以帮我看看这是什么出现了问题。急用，谢谢！
3 v; Q3 X6 G/ i3 K& k$ I; B4 i+ ^

----------------------------------------------------
ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ER
. c0 A6 J! v. z* E' ~5 E* IROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/
# L" ]* j/ ?  EERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ER
% \9 J/ z1 k* C2 jROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/
6 _/ O0 |' O6 r5 _  v6 `: z--------------------------------------------------------------------------------
% O* W- a8 k; U! O----------------------------------------------------
You lose, fella.   The EMTP logic has detected an error condition, and is now go
7 A9 z1 T, i$ f% v8 ?ing to terminate program execution.  The following
; L0 K0 D) Z: J: _: k* l: C4 ?message summarizes the circumstances leading to this situation.  Where an otherw
/ R& a+ H6 ~3 Rise-unidentified data card is referred to, or where
the "last" card is mentioned, it is the most recently read card of the input dat
a that is meant.  The 80-column image of this card
  F" }' b0 ]& L, E$ l- qis generally the last one printed out prior to this termination message.  But po
/ v6 i8 w5 r9 ]) m0 f5 s" Zssibly this last-read card has not yet been
displayed, so a copy follows:
"       3       4.1790373848948505000E-07
! ~+ r  {. `) D; j) T- `8 [  "
              KILL code number                Overlay number               Nearb
y statement number
& E$ F3 A8 i$ t; s                        197                          3
     7656
KILL = 197.   The travel time of the distributed line that is now being read doe
s not exceed the time-step size  DELTAT  (see
floating-point miscellaneous data card).  A mode has just been found with travel
* a8 |" b( a( w7 a8 }' ] time  4.17903738E-07  sec.   Either decrease
DELTAT,  or increase the line length (if in error),  or perhaps even change mode
ling (the requirement disappears if a Pi-circuit
( y: u, L  Y. Owere used instead).
--------------------------------------------------------------------------------
----------------------------------------------------
) g/ T* S7 |" ]$ C6 V5 FERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ER
5 C: x: T1 n) }4 {ROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/
ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ER
: p  T" R, v0 s/ G4 k6 j- pROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/
5 E/ I+ b" C2 R0 M: _+ i3 Z--------------------------------------------------------------------------------
+ Q! ]' M- n5 x: `2 ]----------------------------------------------------

cxxgtxy

回复 1# 星轨
8 @3 q& w) `& i5 W  {
6 c$ x. i- ?3 [, I9 a9 f8 N3 n0 b9 `
( }! N& m1 Z7 V1 \( G6 _    怎么全是error。。。

星轨

回复 2# cxxgtxy
5 B1 `: U; w' y  x& E% a

0 a5 }) t1 F: s3 @- z    这个我也不知道。所以就复制过来，请问下各位老师

星轨

好了，谢谢各位老师。终于看懂了，是说，我的步长设的太大了，我改了一下就可以了。

zmxpig

错误中提示“增加线路长度或者减小步长”

liliang0603

回复 1# 星轨


   好，我也看出来了