|
|
发表于 2011-10-16 15:29:11
|
显示全部楼层
难道是help文件损坏了?: a7 s. r& L$ b q/ [# N! F$ O+ n2 \
help:Name : LINEZT_3 - Distributed parameters (Clarke) 3 phase. Transposed: V) d+ D0 L2 a. F! J9 x& r* i
Card : BRANCH
0 x% M, T2 I8 f5 R2 p( I* v* IData : R/l+= Resistance pr. length in [Ohm/length]. Pos. sequence.
* s& n/ ~" N Y( {* [ R/l0= Resistance pr. length in [Ohm/length]. Zero sequence.2 L2 W \8 _$ W- s' M% L- f' H
{A: ILINE=0: A=inductance L' in [mH/length] if Xopt.=0 }" H$ [( ?' o3 U5 Y
{ A=L' in [ohm/length] if Xopt.=power frequency. }: j) c, R9 e' a' z) @, e9 X$ }3 c
{ ILINE=1: A=Modal surge impedance in [ohm] Z=sqrt(L'/C') }6 ^1 L" U& `8 G' _/ I5 U) M. {
{ ILINE=2: A=Modal surge impedance in [ohm] Z=sqrt(L'/C') }
4 |# `" M4 a% H A+ = Pos. sequence.
) X" |( F& A% b6 | A0 = Zero sequence.
2 O" ?/ v: @* A+ e* [2 Y {B: ILINE=0: B=capacitance C' in [鍲/length] if Copt.=0 }
3 q0 m3 H: |/ G { B=C' in [鍹ho/length] if Copt.=power frequency. }
" @+ N' o, N. T3 p, S) M/ [ { ILINE=1: B=propagation velocity in [length/sec.] v=1/sqrt(C'*L') }
& c+ G! X8 {5 }+ t9 z { ILINE=2: B=modal travel time in [sec] T=sqrt(L'*C')*length }
9 a7 n" u9 z8 }5 W1 V Xopt. and Copt. is set in menu: ATP|Settings/Simulation.
7 c; n4 _9 c% B. ?: T: m* i B+ = Pos. sequence.
2 R% j- i" s" b& f B0 = Zero sequence.! I- R% E. t! A" h5 Q
l = length of line (>0 for transposed lines)" S' g5 [4 O1 n" I
ILINE= Takes values from 0 to 23 ~4 T4 S0 E1 i- k7 q' e
IPUNCH=0: lumped-resistive modelling. G'=0
- E: H6 N& q2 D* X4 ` =1: distortionless-mode modelling. G'=R'*C'/L'
; Y; e2 O+ K3 X* b9 M, S9 K3 A' [# ZNode : IN1= Start node. Letter 'A', 'B' or 'C'
0 E: X$ U2 j g- b( J$ d8 k- p+ U is added to nodename for node 1, 2 and 3.8 C5 F3 C1 f$ j8 s3 W
OUT1= End node. Letter 'A', 'B' or 'C'
, ]) D1 ?: r' P/ l is added to nodename for node 1, 2 and 3.% K5 {7 l& d6 ~# Y5 g
Only branch voltage output is reliable.
- a3 q/ X; H& ^6 @& E8 F2 qRuleBook: IV.D.1 |
|