PSCAD高手必看的啊？who kown？

yizhangsjtu

The story of transmission line is too long to tell here. It needs a graduate course around 30 hours.
( P* G) y3 `7 Q9 F- h1 ?+ ~6 ^
There are following types of line models from simple to sophisticate:
PI section (uncoupled and coupled),
Begron Line
Modal domain frequency dependent line (J. Marti Model)
& i) j7 X# h- _6 D  W0 U) F$ XPhase domain frequency dependent line

If you really need to use those models, you can send inquire Manitoba HVDC Centre (who makes PSCAD).

If you need to understand the theory of those models, you can read EMTP theory book. It is a good start for beginner. The last model is not documented in EMTP theory book. You have to read the paper of Gustavson and Semlyem.
/ B4 O, g/ i9 s8 T
7 _* a( n1 E8 m+ n- r7 O5 t) RHave fun.

xuyufufzu

do you mean the both foundation of the simulate line theory  is the same in the EMTP and PSCAD?
if the answer is affirmed.i should to read carefully the EMTP rulebook .

do you konw how to use the " read file" model.the are some mistakes in my simulation. and i don't know what is matter.

xuyufufzu

i read carefully the  EMTDC Users Guide. is this associate with practice parameter in the normal transformer test? and i can't distill the right parameter for EMTDC form the test such as " no load test" and "short circuit test". what can i do if i what to set right parameter for transformer model?
8 B1 y& y: X* ~" _; ?! `please give me an hand!

yizhangsjtu

1. The line model in EMTP and PSCAD is basically the same in theory;
2. You got to understand the basic theory of transformer before you simulate it. You are recommended to read electric machinery book. PSCAD of EMTP manual would babysitter those basic ideas such as no load loss or short circuit impedance.......
! @, Y7 P. b' f
Some basic course at undergraduate level, such as Electrical Machinery, Power System Analysis, have to be finished before doing simulation with PSCAD or EMTP. It would be almost a requirement the use should have at least first degree to use such complex tools.
3 _. {6 H- `6 }0 Y( s3 ~
& K- C( ~, u5 s, S9 g7 R( zLet's conclude this discussion.

yizhangsjtu

1. The line model in EMTP and PSCAD is basically the same in theory;
/ r7 p5 Y( a0 n2 L0 K4 a2. You got to understand the basic theory of transformer before you simulate it. You are recommended to read electric machinery book. PSCAD of EMTP manual would not babysitter those basic ideas such as no load loss or short circuit impedance.......
2 I& O" b5 ^. j3 m$ a
% i8 I" l8 k, A8 b* D# R# FSome basic course at undergraduate level, such as Electrical Machinery, Power System Analysis, have to be finished before doing simulation with PSCAD or EMTP. It would be almost a requirement the use should have at least first degree to use such complex tools.

xuyufufzu

can you give me an example about "transformer model " and "line model" parameter. i can gain the
$ C% j- m' ?" ?method about to how to  calculate the right parameter. because i have accomplished the prepare with rich foundation of power analysis.

yizhangsjtu

Example of Transformer.

yizhangsjtu

TLINE Example

xuyufufzu

it is very kind of you to give some examples. i must study first.

xuyufufzu

are this examples of the PSCAD? i guess it is . and i know the case .but i can't know how to apply that to the actual transformer.
& p4 P3 ~& r8 \) X! p6 u