--ATP运行仿真雷电过电压出现的问题

jinghaibing

ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/
ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/
------------------------------------------------------------------------------------------------------------------------------------
- \; V' l5 L; MYou lose, fella.   The EMTP logic has detected an error condition, and is now going to terminate program execution.  The following
message summarizes the circumstances leading to this situation.  Where an otherwise-unidentified data card is referred to, or where
the "last" card is mentioned, it is the most recently read card of the input data that is meant.  The 80-column image of this card
) R- T. |* H+ Q, y& V- His generally the last one printed out prior to this termination message.  But possibly this last-read card has not yet been
+ b, N! n& s9 U- ldisplayed, so a copy follows:
& G/ N8 f* E9 b+ I "                                                                                "
              KILL code number                Overlay number               Nearby statement number
                        212                         18                               3522
* Y, w6 q' o5 c  W! a& AKILL = 212.   A Newton solution for  1   coupled nonlinear elements has failed to converge within the iteration limit  MAXZNO = 50.
The current residual is  1.24294193E+04,  which exceeds the sloppy convergence tolerance  EPSTOP = 1.00000000E-01.   The first of
! R  V! w1 w3 w2 E2 _the coupled, true, nonlinear elements (in order of data input) is located in row  1   of the nonlinear element table, and it
8 n( g. V5 U  A! n9 X/ f& Fconnects node  "X0001A"  with node  "B     ".   The final coupled element is in row  1,   and the matrix rank is  1.   Finally, the
: ?* r! y6 P: C8 K  ^simulation time is  T = 4.05000000E-07.   Possible corrective actions include a decrease in the time-step size  DELTAT,  an increase
/ f# Z2 ?. h8 P; j8 O4 n9 lin the iteration limit  MAXZNO,  an increase in the divergence tolerance  EPSTOP,  and artificial splitting of the subnetwork  in
question by distributed-parameter lines (to reduce the number of coupled elements).   In addition, it is possible for the user to
3 P8 _2 ]# ~% m% q4 P5 x. jmake a solution impossible by unrealistically limiting the Newton corrections.  The user should remember that there can be no
* w4 T5 E& ^; ksolution if his bound on arrester voltage is less than the true solution voltage.  The bound has a default value of 1.5 per unit,
. \6 g+ k5 X. R9 v; `2 ]' Halthough it can be changed by a"ZINC OXIDE"  special request (columns 57-64, variable  ZLIN(2)).
------------------------------------------------------------------------------------------------------------------------------------
, Y- p' G7 y# v4 f; B6 z2 q: Z/ VERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/
4 N+ b- W. c/ d1 y5 y* }9 ZERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/
------------------------------------------------------------------------------------------------------------------------------------
3 S( \: u  ]( G, `
Actual List Sizes for the preceding solution follow.       01-Nov-10  17:02:18
   Size  1-10:    56    78   128     7   276     1    73 13840     1     3
' L' w' H; P% }0 P   Size 11-20:     0     6 -9999 -9999 -9999     0     0     0    23  3590
   Size 21-30:   126   375   253     1 -9999    25 -9999 -9999 -9999     0
Seconds for overlays  1-5  :     0.047     0.000     0.047  -- (CP: Wait; Real)
Seconds for overlays  6-11 :     0.000     0.000     0.000
% s# f; {' Y$ p: GSeconds for overlays 12-15 :     0.016     0.000     0.016
Seconds for time-step loop :     0.000     0.000     0.000
Seconds after DELTAT-loop  :     0.000     0.000     0.000
- C- K* m/ m1 j; U" m" w0 t                               ---------------------------
5 O$ p2 ~" w! C) O3 \                   Totals  :     0.063     0.000     0.063

jinghaibing

我做的是输电线路防雷  加的是线路避雷器  可是运行时出现这问题  一直没解决，所以请教各位，我将我的仿真图形附上，请大家看看

liushuaige0919

我的理解是Vref是一个初值，emtp拟合伏安特性曲线用的是牛顿拉夫逊法，你初值隔太远就不会收敛。

wangdc

避雷器参数设置的问题
4 i% r. h8 h  u9 C! I我也遇到了同样的问题
- Z  c* F$ y9 m  V% K: R3 K但也没有很好的解决
! v* y  u! h. W; y我输入的时伏安特性点
可能输入指数好一点
期待高手指点啊

wangdc

可以将参数ErrLim调大一点
但是是否合理就不清楚了

guozh07

: \0 R1 r3 V$ K8 D- `0 J
至少要检查：
1）计算步长是  T = 4.05000000E-07.   要看看你的元件设置，特别是最短的线路单元有多长，如果线路分段很短，减小计算步长。
; Y( A7 r4 F) @6 j$ N- ~2）避雷器参数设置有问题，残压是否太低？

wangdc

报错的信息里说是残压低
7 U8 X, x' m1 k' f/ V! i$ \5 |但是输入的是实际的避雷器的伏安特性时也会出现这种情况啊
还有如何修改MAXZNO = 50？这个参数啊
请斑竹指点啊

jinghaibing

我是按照特高压避雷器的参数输入的  就是不知道如何改

jinghaibing

版主  EPSTOP = 1.00000000E-01  MAXZNO = 50.  这两个是什么意思啊？
- Z6 V0 X( X; y8 W' n% r应该怎么改啊

jinghaibing

版主，请问避雷器参数设置中，Vref这个参数是指避雷器的额定电压吗？

xxyyllxxyyll

加个好友吧，qq543245091，一起学习学习