请问ATP报出如下错误怎么办

星轨

3 w( w0 q" C  }, q9 Y; u

ATP报错截图

" D4 O7 r3 A' s8 H! }6 p' g那位老师可以帮我看看这是什么出现了问题。急用，谢谢！
7 T8 X8 g% }$ N: C& w4 [
, @0 L1 r7 {! D" o# |% n' F
----------------------------------------------------
7 m+ h% O5 \0 Q$ b1 e0 {ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ER
ROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/
ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ER
% i' {# d" y4 l- PROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/
4 t. D- [8 R! x--------------------------------------------------------------------------------
----------------------------------------------------
You lose, fella.   The EMTP logic has detected an error condition, and is now go
ing to terminate program execution.  The following
message summarizes the circumstances leading to this situation.  Where an otherw
ise-unidentified data card is referred to, or where
the "last" card is mentioned, it is the most recently read card of the input dat
a that is meant.  The 80-column image of this card
is generally the last one printed out prior to this termination message.  But po
ssibly this last-read card has not yet been
- R0 ^1 y* m% e& ^5 ~  Edisplayed, so a copy follows:
"       3       4.1790373848948505000E-07
' n% T' ]$ l' |' Q" d0 g  "
              KILL code number                Overlay number               Nearb
y statement number
0 d' d1 Z" _3 i6 j% W1 O( Q                        197                          3
     7656
KILL = 197.   The travel time of the distributed line that is now being read doe
s not exceed the time-step size  DELTAT  (see
floating-point miscellaneous data card).  A mode has just been found with travel
time  4.17903738E-07  sec.   Either decrease
6 H' f* e1 i* ^) Y2 rDELTAT,  or increase the line length (if in error),  or perhaps even change mode
1 v/ G- \& I& W- H7 m$ A7 yling (the requirement disappears if a Pi-circuit
. Z" T8 l9 G. N  r6 _$ Fwere used instead).
- y0 P! ?6 O( p2 ?, f--------------------------------------------------------------------------------
----------------------------------------------------
. [: q/ v( G0 L8 v) X. k$ J- UERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ER
ROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/
ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ER
1 G* y; |( s  t: W7 eROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/
7 e3 i  \! i6 D( t--------------------------------------------------------------------------------
----------------------------------------------------

cxxgtxy

回复 1# 星轨
7 A  R" u( v, i# O# G- _7 g' v
+ G  s- w# `$ k2 X7 ?+ i
. [8 r6 x4 ^1 {! f3 l    怎么全是error。。。

星轨

回复 2# cxxgtxy
) T; m  v8 x' k( k! k
: S% t6 [5 s' H/ ~/ o$ C! E
0 v8 T+ p) D& Q  M0 d4 `    这个我也不知道。所以就复制过来，请问下各位老师

星轨

好了，谢谢各位老师。终于看懂了，是说，我的步长设的太大了，我改了一下就可以了。

zmxpig

错误中提示“增加线路长度或者减小步长”

liliang0603

回复 1# 星轨


   好，我也看出来了