Line Z-T 元件的参数设置问题

yeh

哪位高手 可以告诉我 Line Z-T 元件的参数代表什么，默认单位是多少，还有哪个参数是表示线路长度的？

yeh

哪位好心人指点一下，感激不尽~~~~

maisigete

这。。。看help很容易看懂吧

maisigete

难道是help文件损坏了？
: t+ a+ ]! _& c4 _4 ~) l9 ~) u9 Phelp：Name : LINEZT_3 - Distributed parameters (Clarke) 3 phase. Transposed
4 t" O; M: u: r7 D6 N8 q  v, U5 mCard : BRANCH
Data :  R/l+= Resistance pr. length in [Ohm/length]. Pos. sequence.
: d+ z6 v  d( O) b) f; q        R/l0= Resistance pr. length in [Ohm/length]. Zero sequence.
5 F1 y2 x/ O. T          {A: ILINE=0: A=inductance L' in [mH/length] if Xopt.=0      }
          {            A=L' in [ohm/length] if Xopt.=power frequency. }
          {   ILINE=1: A=Modal surge impedance in [ohm] Z=sqrt(L'/C') }
) t  r3 g- N/ s2 f9 j; U1 B3 E7 F          {   ILINE=2: A=Modal surge impedance in [ohm] Z=sqrt(L'/C') }
        A+  = Pos. sequence.
        A0  = Zero sequence.
          {B: ILINE=0: B=capacitance C' in [鍲/length] if Copt.=0              }
          {            B=C' in [鍹ho/length] if Copt.=power frequency.          }
          {   ILINE=1: B=propagation velocity in [length/sec.] v=1/sqrt(C'*L') }
          {   ILINE=2: B=modal travel time in [sec] T=sqrt(L'*C')*length       }
* H7 s+ G- A$ k) T" m. c% t  L              Xopt. and Copt. is set in menu: ATP|Settings/Simulation.
% T; D' [  z; ?: k* R        B+  = Pos. sequence.
        B0  = Zero sequence.
        l   = length of line (>0 for transposed lines)
" ~# \" d! {# ^5 S, w; W       ILINE= Takes values from 0 to 2
" E* [4 T  F4 p, p6 c8 ~- e9 P      IPUNCH=0: lumped-resistive modelling.    G'=0
% G1 C9 c8 ]! h, I7 P4 ^            =1: distortionless-mode modelling. G'=R'*C'/L'
Node :   IN1= Start node. Letter 'A', 'B' or 'C'
              is added to nodename for node 1, 2 and 3.
        OUT1= End node. Letter 'A', 'B' or 'C'
              is added to nodename for node 1, 2 and 3.
Only branch voltage output is reliable.
) l$ `, Q, ^/ O8 y3 w+ O8 Z  s7 gRuleBook: IV.D.1

yeh

回复 4# maisigete
, v' J& I  @- g8 W7 {3 Z
8 o% ~; r- I5 E' Y! S- m$ o% B
- L  b* o) Q* V- a1 Z4 A    谢谢你，我的Help文件确实损坏了。