plotxy图形不出结果，显示plot必须超过一个节点
仿真出现错误提示为：
You lose, fella. The EMTP logic has detected an error condition, and is now going to terminate program execution.The following
message summarizes the circumstances leading to this situation.Where an otherwise-unidentified data card is referred to, or where
the "last" card is mentioned, it is the most recently read card of the input data that is meant.The 80-column image of this card
is generally the last one printed out prior to this termination message.But possibly this last-read card has not yet been
displayed, so a copy follows:
" "
KILL code number Overlay number Nearby statement number
212 18 3522
KILL = 212. A Newton solution for3 coupled nonlinear elements has failed to converge within the iteration limitMAXZNO = 50.
The current residual is5.15845719E+01,which exceeds the sloppy convergence toleranceEPSTOP = 1.00000000E-01. The first of
the coupled, true, nonlinear elements (in order of data input) is located in row1 of the nonlinear element table, and it
connects node"XX0026"with node"VTB ". The final coupled element is in row3, and the matrix rank is3. Finally, the
simulation time isT = 2.70500000E-06. Possible corrective actions include a decrease in the time-step sizeDELTAT,an increase
in the iteration limitMAXZNO,an increase in the divergence toleranceEPSTOP,and artificial splitting of the subnetworkin
question by distributed-parameter lines (to reduce the number of coupled elements). In addition, it is possible for the user to
make a solution impossible by unrealistically limiting the Newton corrections.The user should remember that there can be no
solution if his bound on arrester voltage is less than the true solution voltage.The bound has a default value of 1.5 per unit,
although it can be changed by a"ZINC OXIDE"special request (columns 57-64, variableZLIN(2)).
------------------------------------------------------------------------------------------------------------------------------------
ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/
ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/
------------------------------------------------------------------------------------------------------------------------------------
Actual List Sizes for the preceding solution follow. 05-Jan-1419:31:31
Size1-10: 37 46 25 1 156 9 30 16298 3 18
Size 11-20: 0 12 -9999 -99993511 0 0 0 23 0
Size 21-30: 55 0 30 3 -9999 9 -99991976 -9999 0
Seconds for overlays1-5: 0.039 0.000 0.039-- (CP: Wait; Real)
Seconds for overlays6-11 : 0.039 0.000 0.039
Seconds for overlays 12-15 : 0.000 0.000 0.000
Seconds for time-step loop : 0.000 0.000 0.000
Seconds after DELTAT-loop: 0.000 0.000 0.000
---------------------------
Totals: 0.078 0.000 0.078
仿真为雷击线路：
仿真设置为
求高人解答 顶楼主一下 如果是Matlab 的话，plotxy要求有两组对应的数组才可以画 顶一下没用过这个 改了一些参数，仿真出来了，但还不明白怎么回事 再帮顶 这个问题我也遇到过，情况和你不一样。我是在运行中点绘图，出现了上述警告，运行到后期（未运行完），依然可以绘图。觉得和ATP的计算速度有关 KILL = 212. A Newton solution for3 coupled nonlinear elements has failed to converge within the iteration limitMAXZNO = 50.
The current residual is5.15845719E+01,which exceeds the sloppy convergence toleranceEPSTOP = 1.00000000E-01.
说的是避雷器的问题，伏安特性曲线的问题，采用指数进行拟合，有时候会不收敛，一般修改伏安特性曲线参数，或者减小仿真步长，也可以降低收敛的最小值 继续顶 好，继续努力。
页:
[1]
2
