求教，怎么读懂LIS文件？
用Jmarti模型的Lcc建立了一个输电线路模型，我想通过生成的LIS文件读出线路的电气参量R，L，C等，不知道可行否？或者怎么从LIS文件读取自己想获取的信息？谢谢各位高人，不胜感激！！！====================================贴一段LIS文件，高手看看=============================
Comment card. NUMDCD = 1. |C data:C:\ATP5\ATP\TEST_LCC1.ATP
Marker card preceding new EMTP data case. |BEGIN NEW DATA CASE
Comment card. NUMDCD = 3. |C --------------------------------------------------------
Comment card. NUMDCD = 4. |C Generated by ATPDRAW十二月, 星期二 22, 2009
Comment card. NUMDCD = 5. |C A Bonneville Power Administration program
Comment card. NUMDCD = 6. |C by H. K. H鴌dalen at SEfAS/NTNU - NORWAY 1994-2008
Comment card. NUMDCD = 7. |C --------------------------------------------------------
Comment card. NUMDCD = 8. |C $DUMMY, XYZ000
Comment card. NUMDCD = 9. |CdT>< Tmax >< Xopt >< Copt >
Misc. data. 1.000E-06 7.500E-02 0.000E+00 | 1.E-6 .075
Misc. data. 500 111100100 | 500 1 1 1 1 0 0 1 0
Comment card. NUMDCD = 12. |C 1 2 3 4 5 6 7 8
Comment card. NUMDCD = 13. |C 345678901234567890123456789012345678901234567890123456789012345678901234567890
Comment card. NUMDCD = 14. |C < n1 >< n2 ><ref1><ref2>< R>< L>< C>
Comment card. NUMDCD = 15. |C < n1 >< n2 ><ref1><ref2>< R>< A>< B><Leng><><>0
Series R-L-C. 1.000E+003.000E-010.000E+00 | XX0001 1.300. 0
Series R-L-C. 5.000E+003.000E-010.000E+00 |X0004AX0002A 5.300. 0
Series R-L-C. 5.000E+003.000E-010.000E+00 |X0004BX0002B 5.300. 0
Series R-L-C. 5.000E+003.000E-010.000E+00 |X0004CX0002C 5.300. 0
Series R-L-C. 2.000E+010.000E+000.000E+00 |XX0005 20. 0
Series R-L-C. 5.000E+001.800E-010.000E+00 |X0003AX0010A 5.180. 0
Series R-L-C. 5.000E+001.800E-010.000E+00 |X0003BX0010B 5.180. 0
Series R-L-C. 5.000E+001.800E-010.000E+00 |X0003CX0010C 5.180. 0
Series R-L-C. 1.500E+020.000E+000.000E+00 |X0003AX0010A 150. 0
Series R-L-C. 1.500E+020.000E+000.000E+00 |X0003BX0010B 150. 0
Series R-L-C. 1.500E+020.000E+000.000E+00 |X0003CX0010C 150. 0
Series R-L-C. 1.000E+013.000E+000.000E+00 |NA XX0015 10.3.E3 0
Series R-L-C. 1.000E+013.000E+000.000E+00 |NB XX0015 10.3.E3 0
Series R-L-C. 1.000E+013.000E+000.000E+00 |NC XX0015 10.3.E3 0
Series R-L-C. 1.000E+003.000E-010.000E+00 |XX0015 1.300. 0
Series R-L-C. 2.000E+002.000E-010.000E+00 |X0010AX0014A 2.200. 0
Series R-L-C. 2.000E+002.000E-010.000E+00 |X0010BX0014B 2.200. 0
Series R-L-C. 2.000E+002.000E-010.000E+00 |X0010CX0014C 2.200. 0
Series R-L-C. 1.000E+013.000E+000.000E+00 |MA XX0001 10.3.E3 0
Series R-L-C. 1.000E+013.000E+000.000E+00 |MB XX0001 10.3.E3 0
Series R-L-C. 1.000E+013.000E+000.000E+00 |MC XX0001 10.3.E3 0
Series R-L-C. 1.500E+020.000E+000.000E+00 |X0004AX0002A 150. 0
Series R-L-C. 1.500E+020.000E+000.000E+00 |X0004BX0002B 150. 0
Series R-L-C. 1.500E+020.000E+000.000E+00 |X0004CX0002C 150. 0
Comment card. NUMDCD = 40. |C $INCLUDE, C:\ATP5\Atp\LIN750_1.lib, X0013A, X0013B, X0013C, X0006A, X0006B $$
Comment card. NUMDCD = 41. |C , X0006C
J. Marti line, mode1 parameters begin. |-1X0013AX0006A 2.0.00 -2 3
J. Marti line, mode2 parameters begin. |-2X0013BX0006B 2.0.00 -2 3
J. Marti line, mode3 parameters begin. |-3X0013CX0006C 2.0.00 -2 3
TR(1,1 )...0.584-0.707-0.421 |0.58387433 -0.70710678 -0.42133648
TI(1,1 )...0.000 0.000 0.000 |0.000000000.000000000.00000000
TR(2,1 )...0.564 0.000 0.803 |0.564075830.000000000.80308851
TI(2,1 )...0.000 0.000 0.000 |0.000000000.000000000.00000000
TR(3,1 )...0.584 0.707-0.421 |0.583874330.70710678 -0.42133648
TI(3,1 )...0.000 0.000 0.000 |0.000000000.000000000.00000000
Comment 你看看填卡格式就明白了
如果是默认的设置（没有特殊申请卡的话） 一般前面两行是步长、仿真时间及输出设置的参数
然后就是网络参数 最后是电源卡及各种要求的输出数据
你自己运行下电路再按F4就是你这个源程序代码了对着填卡的说明书一行一行对一遍 看几个图以后就有经验了
希望对你有所帮助 要是只读电气参数的话，用pi模型或是bergron模型就好了 回复 2# ag9914
请问是在rule book中找到填卡格式的说明吗？我现在有中文版可是并不能很好的利用起来，对于其内容是云里雾里！请指教
页:
[1]
