运行时提示kill=81 线路感应电压仿真
ATP Started at 16:41:28 onMonday, 04 September 2017EMTP begins.Send one offollowing alternatives.SPY, file_name, DISK, HELP, GO, KEY, STOP, BOTH, DIR:Ok,output goes to both disk and screen. Send input datafile name:SPY, file_name, DISK, HELP, GO, KEY, STOP, BOTH, DIR: ---74 cards of disk file read into card cachecells1onward. That was just for nextsubcase. Remainder hasN22 = 2cards. MAXCRD = 30000 Note:Vardim input LISTSIZE.DATcould not beconnected.Use maximum sizes. --- Pass 1. Card = 21.Ready to open $INCLUDE = D:\DOCUME~1\ATPdata\work\3.lib----Illegal file name.Try again .... Alternatively, there maysimply be no privilege to connect the file. File-reading (but notwriting) privilege is required. ? ? ? Trouble with input data.last card number21 isin error.12345678901234567890123456789012345678901234567890123456789012345678901234567890 $INCLUDE, D:\DOCUME~1\ATPdata\work\3.lib, X0001A, X0001B, X0001C, X0003A$$ ------------------------------------------------------------------------------------------------------------------------------------ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/------------------------------------------------------------------------------------------------------------------------------------You lose, fella. The EMTP logichas detected an error condition, and is now going to terminate program execution. The followingmessage summarizes the circumstances leading to this situation.Where an otherwise-unidentified data card is referred to, or wherethe "last" card is mentioned, it is the most recently readcard of the input data that is meant.The 80-columnimage of this cardis generally the last one printed out prior to this terminationmessage.But possibly this last-read card has not yet beendisplayed, so a copy follows: "$INCLUDE,D:\DOCUME~1\ATPdata\work\3.lib, X0001A, X0001B, X0001C, X0003A $$" KILL codenumber Overlay number Nearby statement number 79 1 1227KILL = 79. Sorry.Since interactive EMTP execution (SPY) is notbeing used,correction of the data error that has already beendescribed must await a termination of this simulation. Too bad (interactive correction via SPY might have been possible).------------------------------------------------------------------------------------------------------------------------------------ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/ERROR/------------------------------------------------------------------------------------------------------------------------------------ Temporary error stop inENTRY STOPTP of "WINDOW". NCHAIN, LASTOV = 29 1 12345678901234567890123456789012345678901234567890123456789012345678901234567890 ABUFF(1:80) =$INCLUDE,D:\DOCUME~1\ATPdata\work\3.lib, X0001A, X0001B, X0001C,X0003A $$ ATPFinished at 16:41:28 on Monday, 04 September 2017 Total Execution Time was 0.00 cpu seconds Hit any key to close this window.在做输电线路同塔六回仿真时，提示错误不知道怎么改了，小白一个有大神知道是哪里出问题了吗？求帮助
左端是直流源？ 是交流电流源，前面的错误找到了，但是有出来了新问题，就是仿真出来的结果 特别大，220kV的线路感应电压达到了800kV。不知道哪里出了问题，一直没有找出来::cry::
stoat 发表于 2017-9-15 21:26
左端是直流源？
是直流电流源
牛浩然 发表于 2017-9-18 16:30
是直流电流源
说错了 是交流电流源::sweat::
页:
[1]
